on eligible orders over $150
on eligible orders over $150
Use Fixture Putty to make molds for pad printing operations. Add hardener (Silica Gel) to Fixture Putty to start the chemical reaction necessary to...
View full details200 LPI screen tint (90/10) 10% open area for the second exposure of pad print plates.
TPV Thinner is for use with Marabu Tampa series screen and pad print inks. To regulate ink viscosity, add 10-20% of TPV Thinner to the ink and stir...
View full detailsThinner for Marabu GL Glass ink for screen printing. To regulate ink viscosity, add about 10% of GLTPV Thinner to ink and stir until homogeneous. G...
View full detailsPPTPV Thinner is for use with Maraprop PP ink for thinning pad printing ink. This thinner has a fast evaporation rate. Marabu Pad Printing Auxiliar...
View full detailsUKV-1 Thinner is for use with Marabu pad print and screen print inks. UKV-1 Thinner is for use with Marabu pad printing and screen printing inks. ...
View full detailsSV1 Ink Retarder is used to modify the solvent evaporation rate in Marabu screen and pad print inks. SV-1 has good solubility and an evaporation ra...
View full detailsSV5 Ink Retarder is used to modify the solvent evaporation rate in Marabu screen and pad print inks. Only add SV5 to ink if the drying time needs t...
View full detailsSV9 Ink Retarder is used to modify the solvent evaporation rate in Marabu screen and pad print inks. SV9 has good solubility and an evaporation rat...
View full detailsSafety Data Sheet for Marabu H1 Hardener ** As of Jan. 2023, the 100mL size of this hardener now comes in metal packaging. Different packaging, sam...
View full detailsH2 Hardener is a fast drying ink hardener that produces a hard, brittle ink film and causes yellowing of the ink upon UV exposure. The change in co...
View full detailsABM is a matting paste for use with all 1-component Marabu screen and pad printing inks. When added, AMB will change the degree of gloss in the ink...
View full detailsThe Anti-static Paste AP is an ink additive that reduces ink sensitivity to electrostatic charge. Adding AP paste also thins the ink and decreases ...
View full detailsA930 is a round 4"x3.5" pad and is available in 30, 40 and 50 durometers.
This M60/02P pad is 4.9"L x 3.9"W x 2.6" in dimension and is available in 30, 40, 50 and 60; 30 to 40 durometer in Superflex; and 50 durometer in D...
View full detailsThe AR18 is a high-quality printing pad with a wood base with straight sides suited for printing in tight spots. The pad is available in 30 thr...
View full detailsUse Si-Tech Gel with Fixture Putty to create a mold for pad printing. Once the gel has been worked into the putty a mold can be made, as the putty ...
View full detailsGLH Hardener is recommended for use with Marabu Glass GL Inks only. Add hardener to the ink immediately before printing: 1 part of hardener to 20 p...
View full detailsOpaquing Paste OP 170 increases the opacity and broadens the spectrum when matching color shades or printing onto colored or dark substrates. OP is...
View full detailsA7 is a 2.375" round silicone printing pad and is approximately 40 durometer.
The B-2 is a 3" x 1.25" rectangular silicone printing pad that has an approximate durometer of 40.
1" x 2" rectangle silicone printing pad. Approximately 40 durometer. Use the C8 small 2.1"L x 1.1"H x.4" strip pad to print in smalls, hard to reac...
View full detailsThe 218M is the pad of choice for several major garment manufacturers that print tagless underwear. While the 218M pad is usually available in only...
View full detailsWS73 Water Wash Green plates are steel-backed, photopolymer nylon coated, water wash printing plates that are ready for etching. These plates are t...
View full details